- Correction
- Open access
- Published:
Correction to Acknowledgement
3D Printing in Medicine volume 7, Article number: 37 (2021)
The Original Article was published on 14 September 2021
The Original Article was published on 02 September 2021
The Original Article was published on 31 August 2021
The Original Article was published on 31 August 2021
The Original Article was published on 26 August 2021
The Original Article was published on 07 June 2021
The Original Article was published on 29 April 2021
The Original Article was published on 29 April 2021
Following publication of the articles [1, 2], it is noticed the below sentence needs to be added to the Acknowledgement section of the two articles:
The article processing charge for this publication has been funded by an unrestricted grant from Formlabs.
Following publication of the articles [3,4,5,6,7,8], it is noticed the below sentence needs to be added to the Acknowledgement section of these articles:
The article processing charge for this publication has been funded by an unrestricted grant from Materialise.
The original articles have been updated.
References
Gillett D, Bashari W, Senanayake R, et al. Methods of 3D printing models of pituitary tumors. 3D Print Med. 2021;7:24 https://doiorg.publicaciones.saludcastillayleon.es/10.1186/s41205-021-00118-4.
Ravi P, Chen VCP. A focused simulation-based optimization of print time and material usage with respect to orientation, layer height and support settings for multi-pathological anatomical models in inverted vat photopolymerization 3D printing. 3D Print Med. 2021;7:23 https://doiorg.publicaciones.saludcastillayleon.es/10.1186/s41205-021-00112-w.
Toro M, Cardona A, Restrepo D, et al. Does vaporized hydrogen peroxide sterilization affect the geometrical properties of anatomic models and guides 3D printed from computed tomography images? 3D Print Med. 2021;7:29 https://doiorg.publicaciones.saludcastillayleon.es/10.1186/s41205-021-00120-w.
De Backer P, Allaeys C, Debbaut C, et al. Point-of-care 3D printing: a low-cost approach to teaching carotid artery stenting. 3D Print Med. 2021;7:27 https://doiorg.publicaciones.saludcastillayleon.es/10.1186/s41205-021-00119-3.
Hopfner C, Jakob A, Tengler A, et al. Design and 3D printing of variant pediatric heart models for training based on a single patient scan. 3D Print Med. 2021;7:25 https://doiorg.publicaciones.saludcastillayleon.es/10.1186/s41205-021-00116-6.
Orecchia L, Manfrin D, Germani S, et al. Introducing 3D printed models of the upper urinary tract for high-fidelity simulation of retrograde intrarenal surgery. 3D Print Med. 2021;7:15 https://doiorg.publicaciones.saludcastillayleon.es/10.1186/s41205-021-00105-9.
Willemsen K, Ketel MHM, Zijlstra F, et al. 3D-printed saw guides for lower arm osteotomy, a comparison between a synthetic CT and CT-based workflow. 3D Print Med. 2021;7:13 https://doiorg.publicaciones.saludcastillayleon.es/10.1186/s41205-021-00103-x.
Ruiz OG, Dhaher Y. Multi-color and Multi-Material 3D Printing of Knee Joint models. 3D Print Med. 2021;7:12 https://doiorg.publicaciones.saludcastillayleon.es/10.1186/s41205-021-00100-0.
Author information
Authors and Affiliations
Consortia
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/. The Creative Commons Public Domain Dedication waiver (http://creativecommons.org/publicdomain/zero/1.0/) applies to the data made available in this article, unless otherwise stated in a credit line to the data.
About this article
Cite this article
3D Printing in Medicine. Correction to Acknowledgement. 3D Print Med 7, 37 (2021). https://doiorg.publicaciones.saludcastillayleon.es/10.1186/s41205-021-00126-4
Published:
DOI: https://doiorg.publicaciones.saludcastillayleon.es/10.1186/s41205-021-00126-4